Download New Updated (July) Juniper JN0-360 Actual Test 91-100

Ensurepass

 

QUESTION 91

Click the Exhibit button. Referring to the exhibit, which statement is correct?

 

— Exhibit —

 

{master}[edit]

 

user@router-RE0# run show task replication

 

Stateful Replication: Enabled

 

RE mode. Master

 

Protocol Synchronization Status

 

OSPF Complete

 

RIP Complete

 

BGP Complete

 

MPLS Complete

 

LDP Complete

 

{master}[edit]

 

user@router-RE0# run show bgp summary | match 192.168.1.1

 

192.168.1.1 65056 288 327 0 2 1:05 Establ

 

{backup}[edit]

 

user@router-RE1# run show system switchover

 

Graceful switchover: On

 

Configuration database. Ready

 

Kernel database. Ready

 

Peer state. Steady State

 

{backup}[edit]

 

user@router-RE1# run show bgp summary | find 192.168.1.1

 

192.168.1.1 65
056 592 737 3778 2 1:33 Establ

 

{backup}[edit]

 

user@router-RE1# run show bgp replication

 

Synchronization master:

 

Session state. Up, Since. 6d 20:42:51

 

Flaps: 1, Last flap reason: Commit-sync error

 

Protocol state. Idle, Since. 5d 19:41:52

 

Synchronization state. Complete

 

Number of peers waiting. AckWait: 0, SoWait: 0, Scheduled. 0

 

rsync walk at: inet.0 – , queued 0

 

Messages sent: Open 1, Establish 7415, Update 17, Error , Complete 48

 

Messages receiveD. Open 1, Request 1 wildcard 47 targeted, EstablishAck 2827, CompleteAck 4

 

— Exhibit —

 

A.

An RE switchover is likely to result in BGP disruption, but no dataplane impact will be seen.

B.

An RE switchover is likely to result in BGP disruption which will also effect the dataplane.

C.

The system is not yet GRES ready, you need to wait for kernel synchronization to complete.

D.

The system is NSR ready and a switchover should be hitless to the BGP control and data plane.

 

Correct Answer: D

 

 

QUESTION 92

You are asked to establish an MPLS LSP between two sites. You are required to ensure the LSP traverses specific routers within your network. Which solution is correct?

 

A.

Enable traffic engineering within LDP and define the explicit route the LSP must follow.

B.

Implement RSVP and define the explicit route the LSP must follow.

C.

Enable traffic engineering within RSVP and define the explicit route the LSP must follow.

D.

Implement LDP and define the explicit route the LSP must follow.

 

Correct Answer: B

 

 

QUESTION 93

In which environment would you run BGP?

 

A.

a company spread across multiple floors of a building

B.

a company with a single office

C.

a home network

D.

the public Internet

 

Correct Answer: D

 

 

QUESTION 94

What are two differences between RSTP and VSTP? (Choose two.)

 

A.

Using VSTP, the BPDU destination address is always 01:00:0C:CC:CC:CD.

B.

Using VSTP, the BPDU frame carries an 802.1Q tag.

C.

Using RSTP, the BPDU destination address is always 01:00:0C:CC:CC:CD.

D.

Using RSTP, the BPDU frame carries an 802.1Q tag.

 

Correct Answer: AB

 

 

QUESTION 95

Which two statements are true about MPLS VPNs? (Choose two.)

 

A.

With Layer 3 VPNs, the provider’s routers participate in the customer’s Layer 3 routing.

B.

MPLS VPNs are designed to run over private networks rather than the public Internet.

C.

With Layer 2 VPNs, the provider does not participate in the routing of the customer’s private IP traffic.

D.

MPLS VPN tunnels are always encrypted.

 

Correct Answer: AC

 

 

QUESTION 96

Which three BGP attributes must be sent to EBGP peers? (Choose three.)

 

A.

local preference

B.

atomic aggre
gator

C.

origin

D.

next hop

E.

AS path

 

Correct Answer: CDE

 

 

QUESTION 97

Which two statements are true about unified ISSU? (Choose two.)

 

A.

It allows gradual implementation of new features.

B.

It reduces operating costs while delivering higher service levels.

C.

It involves network down time during software image upgrades.

D.

It requires graceful Routing Engine switchover (GRES) and nonstop active routing (NSR).

 

Correct Answer: BD

 

 

QUESTION 98

You are configuring OSPF on a Junos device; however, you have not configured a router ID. What is the default behavior in this situation?

 

A.

If the loopback is configured with a 127/8 address, it will be used.

B.

If the loopback is not configured, it will use the interface with the highest IP address.

C.

If the loopback is configured and does not have a usable address, the IP address associated with the first hardware interface is used.

D.

If you configure a dedicated management address and include that interface in OSPF, it will be used as the router ID.

 

Correct Answer: C

 

 

QUESTION 99

Which routing table contains the route information for the user-defined routing instance called Candidate1?

 

A.

inet.Candidate1.0

B.

Candidate1.inet.0

C.

inet.0

D.

Candidate1-inet.0

 

Correct Answer: B

 

QUESTION 100

A rogue switch has been added to your network, exchanged BPDUs, and is now part of the spanning tree topology. Which feature would help prevent this from happening in the future?

 

A.

storm control

B.

BPDU control

C.

root protection

D.

loop protection

 

Correct Answer: B

 

Free VCE & PDF File for Juniper JN0-360 Real Exam

Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …

This entry was posted in JN0-360 Real Tests (July) and tagged , , , , , , . Bookmark the permalink.