Download New Updated (June) VMWare VCPN610 Practice Test 31-40

Ensurepass

 

QUESTION 31

Which two are pieces of information required to perform an NSX backup? (Choose two.)

 

A.

Transfer protocol

B.

Default Port

 

 

 

VMware VCPN610 : Practice Test

C.

Number of backups retained

D.

Filename prefix

 

Answer: AD

 

 

QUESTION 32

An administrator has deployed and powered on a new virtual machine configured to get its networking information via DHCP. The virtual machine is connected to an NSX network and connectivity has been verified. After reconfiguring the virtual machine with a static IP address, network connectivity is lost.

 

Which statement explains what happened?

 

A.

SpoofGuard is disabled

B.

SpoofGuard is enabled and the operation mode is set to automatic

C.

SpoofGuard is enabled and the operation mode is set to manual

D.

SpoofGuard is enabled but not configured

 

Answer: B

 

 

QUESTION 33

Where are the distributed NSX firewall decisions logged?

 

A.

NSX Manager

B.

vCenter Server

C.

NSX Edge

D.

ESXi host

 

Answer: D

 

 

QUESTION 34

Which statement best describes firewall packet processing in an NSX environment?

 

 

 

VMware VCPN610 : Practice Test

 

A.

Packets that require firewall processing are redirected to the nearest ESXi host deployed with a virtual machine based firewall.

B.

Packets that require firewall processing are forwarded to a physical firewall appliance.

C.

Packets that require firewall processing are processed in-line on the local hypervisor.

D.

Packets that require firewall processing are forwarded to the nearest ESXi host with an embedded firewall module.

&nbsp

;

Answer: C

 

 

QUESTION 35

An NSX Edge Service Gateway has two interfaces:

 

?Internal interface named Internal Access

 – IP address = 10.10.10.1

 – Network mask = 255.255.255.0

 

?Uplink interface named Physical Uplink

 – IP address = 20.20.20.1

 – Network mask = 255.255.255.0

 

A vSphere administrator wants to add a SNAT rule to allow traffic from the internal network segment to access external resources via the uplink interface.

 

Which three steps should the vSphere administrator do to add the SNAT rule? (Choose three)

 

A.

Apply the SNAT rule to the Internal Access interface.

B.

Select 10.10.10.1 as the translated source IP.

C.

Apply the SNAT rule on the Physical Uplink interface.

D.

Select 10.10.10.0/24 as the original subnet.

E.

Choose 20.20.20.2 as the translated source IP.

 

Answer: CDE

 

 

QUESTION 36

VMware VCPN610 : Practice Test

Which components are required to enable layer 2 bridging? (Choose two.)

 

A.

Distributed firewall rule to allow layer 2 traffic in the bridge.

B.

Deployed Logical Switch.

C.

Deployed Logical Router.

D.

VLAN trunk configured on logical switch.

 

Answer: AC

 

 

QUESTION 37

You are tasked with designing a data center architecture that should maximize the use of vMotion within your environment. You must use these VMware best practices:

 

The network must utilize widely offered layer 2 switching and layer 3 switching services

Purchase of new equipment should be minimized

 

Which two network design architectures will provide the requirements for vMotion in your data center? (Choose two.)

 

A.

Utilize layer 3 switching from the access layer through the core.

B.

Employ layer 2 multipathing using a standardized protocol.

C.

Deploy a flat, traditional layer 2 switched network.

D.

Deploy an overlay technology for the deployment of your virtual network.

 

Answer: AD

 

 

QUESTION 38

A network security administrator wants to monitor traffic on several VLANs configured on a vSphere Distributed Switch. The traffic will be sent to another distributed port.

 

What type of port mirroring session must be configured to meet these requirements?

 

A.

Select the session type Distributed Port Mirroring when configuring the Port Mirroring session.

B.

Select the session type Remote Mirroring Source when configuring the Port Mirroring session.

 

 

 

VMware VCPN610 : Practice Test

C.

Select the session type Remote Mirroring Destination when configuring the Port Mirroring session.

D.

Select the session type Distributed Port Mirroring (legacy) when configuring the Port Mirroring session.

 

Answer: C

 

 

QUESTION 39

What is a prerequisite to deploying a Logical Switch?

 

A.

Configure the VXLAN Tunnel Endpoint’s (VTEP) VLAN on the trunk in the physical switches.

B.

Add the ESXi hosts to the same vSphere Distributed Switch.

C.

Prepare and configure VTEPs on the ESXi hosts using the vSphere Web Client.

D.

Create a port group on the vSphere Distributed Switch.

 

Answer: A

 

 

QUESTION 40

A Distributed Router and an NSX Edge Gateway are connected to a Logical Switch with a VNI of 7321. Both also have connections to the external network.The Distributed Router serves as the default gateway for the virtual machines in VNI 7321.

 

A vSphere administrator does not want to advertise the subnet in VNI 7321 to the rest of the network, but still wants to allow virtual machines in the segment to access external resources.

 

What two steps should the vSphere administrator take to achieve this? (Choose two)

 

A.

Make the NSX Edge Gateway the default gateway for VNI 7321.

B.

Configure a SNAT rule for VNI 7321 on the NSX Edge Gateway.

C.

Configure a static route to the NSX Edge Gateway in the upstream router.

D.

Create an inbound Access Control List on the Distributed Router.

 

Answer: AB

VMware VCPN610 : Practice Test

 

Free VCE & PDF File for VMWare VCPN610 Real Exam

Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …

This entry was posted in VCPN610 Practice Tests (June) and tagged , , , , , , . Bookmark the permalink.