[Free] 2018(Jan) EnsurePass Dumpsleader Juniper JN0-533 Dumps with VCE and PDF 21-30

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Juniper Official New Released JN0-533
100% Free Download! 100% Pass Guaranteed!

FWV, Specialist (JNCIS-FWV)

Question No: 21

You have the following BGP configuration in place to establish a session with a remote peer over your ethernet4 interface.

set vrouter trust-vr protocol bgp 65000 set vrouter trust-vr protocol bgp enable

set vrouter trust-vr protocol bgp neighbor remote-as 65500 set vrouter trust-vr protocol bgp neighbor enable

Which additional statement is necessary to establish the session?

  1. set interface protocol bgp enable

  2. set interface ethernet4 bgp enable

  3. set vrouter trust-vr protocol bgp interface ethernet4

  4. set interface ethernet4 protocol bgp

Answer: D

Question No: 22

Which action does a ScreenOS device perform first when processing a packet?

  1. It checks for an existing session.

  2. It checks for attacks in the payload.

  3. It performs a route lookup.

  4. It performs a policy lookup.

Answer: A

Question No: 23

You have been making changes on an NSRP cluster and find that the ScreenOS devices are out of sync. You want to synchronize the devices#39; configurations together.

Which command and process are needed to accomplish this task?

  1. Run the command set nsrp sync global-config check-sum on the local device and then reset the peer device.

  2. Run the command set nsrp sync global-config save on the backup device and then reset the backup device.

  3. Run the command exec nsrp sync config save on the peer device and then reset the peer device.

  4. Run the command exec nsrp sync global-config save on the backup device and then reset the backup device.

Answer: D

Question No: 24

What are three policy types? (Choose three.)

  1. destination-based policy

  2. intrazone policy

  3. source-based policy

  4. interzone policy

  5. global zone policy

Answer: B,D,E

Question No: 25

A routing table contains an IBGP route, a RIP route, an OSPF external Type 2 route, and an EBGP route for the routerreceives traffic destined for,which route will the router use by default?

  1. the EBGP route

  2. the IBGP route

  3. the OSPF route

  4. the RIP route

Answer: A

Question No: 26

A monitored interface on a clustered pair of ScreenOS devices goes down and both devices became ineligible to be master of the cluster. As a result, neither device is passing traffic.

Which step would have prevented this situation?

  1. Configure initial hold-down time to 10 seconds.

  2. Configure the preempt parameter and a higher priority on one of the devices.

  3. Configure the lost heartbeat interval to 1 second.

  4. Configure the master-always-exists parameter.

Answer: D

Question No: 27

What is a zone?

  1. a set of rules that controls traffic from a specified source to a specified destination using a specified service

  2. a collection of subnets and interfaces sharing identical security requirements

  3. a method of providing a secure connection across a network

  4. a tool to protect against DoS attacks

Answer: C

Question No: 28

Which two statements are correct about internal antivirus scanning? (Choose two.)

  1. It includes a predefined file extension list for each protocol.

  2. It allows you to load-balance ICAP scan servers.

  3. It requires you to install a ScreenOS software license.

  4. It provides inbound spyware and phishing protection.

Answer: C,D

Question No: 29

– Exhibit –

Date Time Module Level Type Description

2012-11-30 12:49:41 system warn 00528 SSH: Password authentication failed for admin user #39;firewall-user#39; at host

2012-11-30 12:49:41 system warn 00518 ADM: Local admin authentication failed for login name firewall-user: invalid

login name

2012-11-30 12:49:28 system info 00536 IKE Phase 1:

Retransmission limit has been reached.

2012-11-30 12:42:23 system notif 00531 The system clock was updated from primary NTP server type

with an adjustment of 234 ms. Authentication was None. Update mode was Automatic

– Exhibit –

Based on the output shown in the exhibit, in which log were these events displayed?

  1. event

  2. self

  3. login

  4. traffic

Answer: A

Question No: 30

You are using interface-based NAT for traffic passing from the trust zone to the untrust zone.

What will occur?

  1. The source IP address is not translated.

  2. The source IP address is translated to the trust interface IP address.

  3. The network address and port translation (NAPT) is performed on the loopback interface.

  4. The source IP address is translated to the untrust interface IP address.

Answer: D

100% Ensurepass Free Download!
Download Free Demo:JN0-533 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-533 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

This entry was posted in JN0-533 Latest Exam (Jan 2018) and tagged , , , , , , , . Bookmark the permalink.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.