[Free] 2018(Jan) EnsurePass Dumpsleader Juniper JN0-691 Dumps with VCE and PDF 81-90

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Juniper Official New Released JN0-691
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-691.html

Junos Troubleshooting

Question No: 81 – (Topic 2)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

You recently added an EBGP neighbor to R1 and you are receiving a single BGP route for their internal network. You notice that on R2 the route learned from C1 is being marked as hidden because the next hop is unusable.

Referring to the exhibit, what should you do to resolve the problem?

  1. Create a next-hop-self import policy on R2 and apply this policy to IBGP.

  2. Create a next-hop-self export policy on R1 and apply this policy to IBGP.

  3. Create a next-hop-self import policy on R1 and apply this policy to EBGP.

  4. Create a next-hop-self import policy and apply this policy to IBGP.

Answer: B

Question No: 82 – (Topic 2)

Which route would a packet destined to 192.168.14. take?

A. 192.168.14.0/24 *[BGP/100] B. 192.168.14.0/24 *[BGP/70] C. 192.168.14.0/24 *[BGP/200] D. 192.168.64.0/21 *[Direct/0]

Answer: B

Question No: 83 – (Topic 2)

You are notified about a router reboot event.

Which command would be helpful in determining the reason for the last reboot?

  1. show chassis craft-interface

  2. show system reboot

  3. show chassis routing-engine

  4. show system snapshot

Answer: C

Question No: 84 – (Topic 2)

Which process is responsible for managing interface devices on the system?

  1. chassis daemon

  2. device control daemon

  3. routing protocol process

  4. management daemon

Answer: B

Question No: 85 – (Topic 2)

Which three steps are involved in troubleshooting any problem? (Choose three.)

  1. Reboot the device.

  2. Clearly define the problem.

  3. Outline the expected behavior.

  4. Determine who made the changes.

  5. Isolate the problem.

Answer: B,C,E

Question No: 86 – (Topic 2)

You have configured and successfully committed the configuration for nonstop active routing (NSR).Which command would you use to determine if NSR is operating correctly?

  1. Use the show system synchronization command on the master and the backup Routing Engines.

  2. Use the show task replication command only on the master Routing Engine.

  3. Use the show task replication command on the master and the backup Routing Engines.

  4. Use the show system synchronization command only on the master Routing Engine.

Answer: C

Question No: 87 – (Topic 2)

Click the Exhibit button.

– Exhibit –

user@routergt; show snmp statistics

SNMP statistics: Input:

Packets: 246213, Bad versions: 12, Bad community names: 12, Bad community uses: 0, ASN parse errors: 0,

Too bigs: 0, No such names: 0, Bad values: 0, Read onlys: 0, General errors: 0,

Total request varbinds: 227084, Total set varbinds: 67, Get requests: 44942, Get nexts: 1 , Set requests: 10712, Get responses: 0, Traps: 0,

Silent drops: 0, Proxy drops: 0, Commit pending drops: 0, Throttle drops: 0,

V3 Input:

Unknown security models: 0, Invalid messages: 0 Unknown pdu handlers: 0, Unavailable contexts: 0 Unknown contexts: 0, Unsupported security levels: 0 Not in time windows: 0, Unknown user names: 0

Unknown engine ids: 0, Wrong digests: 0, Decryption errors: 0 Output:

Packets: 246093, Too bigs: 0, No such names: 0,

Bad values: 0, General errors: 0,

Get requests: 0, Get nexts: 0, Set requests: 0,

Get responses: 246025, Traps: 0

– Exhibit –

A new SNMP session has recently been implemented on this router and is experiencing

problems sending and receiving SNMP information.

Referring to the exhibit, which two problems are indicated by the received messages from the NMS? (Choose two.)

  1. unsupported SNMP community name

  2. unknown SNMP community name

  3. unsupported SNMP version indicated

  4. invalid SNMP version indicated

Answer: B,C

Question No: 88 – (Topic 2)

An interface on your Junos device reports a device-level flag of Loopback-detected. What is causing this flag to be reported?

  1. The link-layer protocol failed to successfully connect with the remote endpoint.

  2. The interface was administratively disabled.

  3. The interface is in promiscuous mode and sees frames addressed to all physical addresses on the medium.

  4. The interface link layer received its own frames.

Answer: D

Question No: 89 – (Topic 2)

Click the Exhibit button.

– Exhibit –

user@R1gt; show route 2.2.2.2

user@R1gt; show route forwarding-table destination 2.2.2.2 Routing table:default.inet

Internet:

Destination Type RtRef Next hop Type Index NhRef Netif 2.2.2.2/32 user 1 17.1.1.2 ucst 642 9 xe-1/1/0.0

– Exhibit –

Referring to the exhibit, which statement is true about transit traffic sent to 2.2.2.2?

  1. R1 will discard the packet.

  2. R1 will forward the packet.

  3. R1 will redirect the packet to the Routing Engine.

  4. R1 will reject the packet.

Answer: B

Question No: 90 – (Topic 2)

Which CLI command applies the candidate configuration to the active configuration?

  1. load

  2. merge

  3. copy run start

  4. commit

Answer: C

100% Ensurepass Free Download!
Download Free Demo:JN0-691 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-691 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

This entry was posted in JN0-691 Latest Exam (Jan 2018) and tagged , , , , , , , . Bookmark the permalink.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.