[Free] 2018(Jan) EnsurePass Examcollection Juniper JN0-692 Dumps with VCE and PDF 61-70

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Juniper Official New Released JN0-692
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-692.html

Service Provider Routing and Switching Support, Professional

Question No: 61 – (Topic 1)

Ensurepass 2018 PDF and VCE

Which two scenarios would explain the error shown in the exhibit? (Choose two.)

  1. Packets were dropped in the receive path of the local router.

  2. The local router received a route withdrawal from the peer.

  3. Packets were dropped in the receive path of the peer router.

  4. The local router egress interface towards the peer was congested.

Answer: C,D

Question No: 62 – (Topic 1)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

In the exhibit, R1 is a route reflector and R2 through R5 are clients in a full mesh configuration. R2 should only receive one copy of all routes sent from R5.Which configuration is valid?

Ensurepass 2018 PDF and VCE

  1. Option A

  2. Option B

  3. Option C

  4. Option D

Answer: C

Question No: 63 – (Topic 1)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

Referring to the exhibit, which statement is correct?

  1. Only multicasts packets (224.0.1.39) are allowed on the input and output direction.

  2. Auto-RP discovery messages are filtered in the input and output direction.

  3. Rendezvous point announcements are filtered in the output direction.

  4. This filter does not work because the input or output parameter is missing.

Answer: C

Question No: 64 – (Topic 1)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

In the exhibit, what happens if the source starts sending multicast traffic toward R1 and there are receivers registered at the RP?

  1. R1 encapsulates the multicast packets into a PIM register multicast packet.

  2. R1 encapsulates the multicast packets into PIM join unicast messages.

  3. R1 forwards the multicast packets on the S,G tree towards the RP.

  4. R1 tunnels the multicast packets in PIM register messages toward the RP.

Answer: D

Question No: 65 – (Topic 1)

One of your router#39;s OSPF adjacencies is down.

What are three reasons for this adjacency state change? (Choose Three)

  1. A filter has just been configured on one of the OSPF routers.

  2. The OSPF hello value is the same on both routers.

  3. The controlling BFD session state has gone down.

  4. The authentication key on both routers matches.

  5. One of the physical interfaces has gone down.

Answer: A,C,E

Question No: 66 – (Topic 1)

Ensurepass 2018 PDF and VCE

You have configured an IS-IS adjacency between routers R1 and R2. However, the adjacency is not coming up. Referring to the exhibit, what appears to be the problem?

  1. The R2 interface is down.

  2. The ge-1/1/2.0 interface has IS-IS level 2 disabled.

  3. The ge-1/1/2.0 interface does not have family iso configured.

  4. The ge-1/1/2.0 interface has IS-IS level 1 disabled.

Answer: C

Question No: 67 – (Topic 1)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

A customer is using the Layer 3 VPN multicast technology shown in the exhibit. Which statement is true?

  1. PE6 sends a BGP NG-MVPN NLRI Type 5 message upon receiving a *,G join on its VRF interface.

  2. PE6 sends a BGP NG-MVPN NLRI Type 7 message upon receiving an S,G join on its VRF interface.

  3. The P2MP sub LSP reduces the traffic load on the interface between PE2 and PE5.

  4. PE6 signals PE2 through MBGP to include the I-PMSI tree on its P2MP sub LSP.

Answer: B

Question No: 68 – (Topic 1)

Click the Exhibit button.

Ensurepass 2018 PDF and VCE

Customer A is complaining that CE1 and CE2 cannot form an OSPF adjacency across your LDP Layer 2 circuit. The physical topology of the network is CE1-PE1-P-PE2-CE2. PE1#39;s loopback is 192.168.5.1, P#39;s loopback is 192.168.6.1, and PE2#39;s loopback is 192.168.7.1.

Referring to the output in the exhibit, what is the problem?

  1. mismatched virtual circuit ID values

  2. mismatched interface encapsulations

  3. incorrect PE-CE interface configuration

  4. extended LDP neighbor not established

Answer: B

Question No: 69 – (Topic 1)

Ensurepass 2018 PDF and VCE

You have committed a configuration on router R1 as shown in the exhibit. However, it resulted in a (*, G) join for only one group (228.1.1.1) on R1.

Which additional configuration would result in the creation of a (*, G) join for the other group (232.1.1.1)?

  1. Add relevant configurations for an SSM map.

  2. Enable PIM version 1 on interface xe-5/2/0.0.

  3. Configure another RP for the other group

  4. Enable PIM on all interfaces.

Answer: A

Question No: 70 – (Topic 1)

Your currently configured regular expression does not match the AS path shown below: 2135 55 55 55 55 3796

Which three regular expressions would match this path? (Choose three.)

A. quot;.quot;2135quot;

B. quot;2135.*quot;

C. quot;* 55(1, 3) *quot;

D. quot;2135 55(5) 3796quot;

E. quot;2135 55(1, 2) 3796quot;

Answer: B,C,E

Topic 2, Volume B

100% Ensurepass Free Download!
Download Free Demo:JN0-692 Demo PDF
100% Ensurepass Free Guaranteed!
JN0-692 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

This entry was posted in JN0-692 Latest Exam (Jan 2018) and tagged , , , , , , , . Bookmark the permalink.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.