[Free] Download New Latest (November) Juniper JN0-531 Actual Tests Topic 1 part 01

Ensurepass

QUESTION 73  (Topic 1)

 

You have four policies configured for the egress interface with 10 Mbps physical bandwidth. The policies are configured as follows:

 

Policy 1 – Highest Priority, 1 Mbps guaranteed, 3 Mbps maximum

 

Policy 2 – 1st Priority, 1 Mbps guaranteed, 4 Mbps maximum

 

Policy 3 – 1st Priority, 2 Mbps guaranteed, 2 Mbps maximum

 

Policy 4 – Highest Priority, 2 Mbps guaranteed, 4 Mbps maximum

 

Assuming the policies are processed in the order shown, which policy will drop traffic first under a full load?

 

A.

Policy 1

B.

Policy 2

C.

Policy 3

D.

Policy 4

 

Answer: D

 

 

QUESTION 74  (Topic 1)

 

Which command shows the present debugging configuration?

 

A.

get conf

B.

get dbuf

C.

get debug

D.

debug info

 

 

 

 

 

Answer: C

 

 

QUESTION 75  (Topic 1)

 

You enable run time object (RTO) sync on the NSRP cluster. Which command will provide RTO message sync counters?

 

A.

get nsrp rto

B.

get count stat

C.

get rto counter

D.

get nsrp counter

 

Answer: D

 

 

QUESTION 76  (Topic 1)

 

Click the Exhibit button.

 

In the exhibit, which two can be determined about the VPN? (Choose two.)

 

clip_image002

 

A.

NAT-traversal is enabled.

B.

The rekey interval is 8 hours.

C.

This device initiated the Phase 1 negotiations.

D.

The certificate used in this exchange is set to never expire.

 

Answer: BC

 

 

 

 

 

QUESTION 77  (Topic 1)

 

Which command is used to verify that IGMP is running correctly?

 

A.

get route igmp

B.

get igmp query

C.

set igmp query interface e0/1

D.

exec igmp interface e0/1 query

 

Answer: D

 

 

QUESTION 78  (Topic 1)

 

You want to configure routing redundancy over your VPN network, but do not want to deploy a dynamic routing protocol. What should you do?

 

A.

Configure multiple static routes, setting tags to designate primary and backup routes.

B.

Configure multiple static routes, adjusting the cost to determine primary and backup routes.

C.

Configure multiple static routes, adjusting the metric to determine primary and backup routes.

D.

Configure multiple static routes, adjusting the preference to create floating static routes as backups.

 

Answer: C

 

 

QUESTION 79  (Topic 1)

 

Click the Exhibit button.

 

In the output shown, w
hich single command is entered out of order?

 

clip_image004

 

A.

set ffilter

B.

undebug all

C.

get dbuf stream

 

 

 

 

D.

debug flow basic

 

Answer: < /span>B

 

 

QUESTION 80  (Topic 1)

 

What should you configure to insure an HA cable failure does not result in both devices attempting to become master?

 

A.

failover count

B.

secondary path

C.

monitor threshold

D.

heartbeat threshold

 

Answer: B

 

 

QUESTION 81  (Topic 1)

 

You have configured NSRP Active/Active with vsd-group 0 as master on device A and vsd- group 1 as master on device

B.Both the devices are active and are masters for their respective VSDs. What will happen to the traffic for vsd-group 1 if received on device A?

 

A.

The traffic will be dropped on device A.

B.

The traffic will be handled locally on device

A.

C.

The traffic will be forwarded to device B over the HA link.

D.

Device A will inform the sender to re-direct traffic to device B.

 

Answer: C

 

 

QUESTION 82  (Topic 1)

 

You have enabled RIP in a hub and spoke VPN environment, using demand circuits. You are not receiving routes from one of your spokes, although the VPN is up. When you debug RIP on the spoke device, you see regular RIP updates being generated on the tunnel interface. You are receiving and sending routes to the rest of your spokes. What is the problem?

 

A.

You did not disable split horizon on the spoke device.

B.

You did not configure demand circuit on the spoke device.

 

 

 

 

C.

You did not configure passive interface on the spoke device.

D.

You did not configure a RIP neighbor for the spoke device on the hub.

 

Answer: B

 

Free VCE & PDF File for Juniper JN0-531 Actual Tests

Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …

This entry was posted in JN0-531 Actual Tests (November) and tagged , , , , , , . Bookmark the permalink.