[Free] Download New Latest (November) Juniper JN0-532 Actual Tests 21-30

Ensurepass

QUESTION 21

You have enabled RIP in a hub and spoke VPN environment, using demand circuits. You are not receiving routes from one of your spokes, although the VPN is up. When you debug RIP on the spoke device, you see regular RIP updates being generated on the tunnel interface. You are receiving and sending routes to the rest of your spokes.

 

What is the problem?

 

A.

You did not disable split horizon on the spoke device.

B.

You did not configure demand circuit on the spoke device.

C.

You did not configure passive interface on the spoke device.

D.

You did not configure a RIP neighbor for the spoke device on the hub.

 

 

Answer: B

 

 

QUESTION 22

You have entered the following BGP configuration:

 

Setvrouter trust-vr bgp 65530

Setvrouter trust-vr bgp enable

Setvrouter trust-vr protocol bgp neighbor 1.1.1.250 remote-as 65500 Setvrouter trust-vr protocol bgp neighbor 1.2.3.250 remote-as 65280

 

BGP is not working. What two elements are missing from your configuration? (Choose two.)

 

A.

You have not enabled the BGP peers.

B.

You have not enabled EBGP multihop.

C.

You have not placed the peers in a BGP peer group.

D.

You have not enabled BGP on the interfaces connecting to the peers.

 

Answer: AD

 

 

QUESTION 23

Which ScreenOS CLI command would be used for copying routes in the untrust-vr to OSPF in the trust-vr?

 

A.

set vrouter trust-vr ospf export vrouter untrust-vr address to-trust

B.

set vrouter untrust-vr export list to-trust vrouter trust-vr protocol ospf

C.

set vrouter untrust-vr export-to vrouter trust-vr route-map to-trust protocol ospf

D.

set vrouter trus
t-vr protocol ospf import-from vrouter untrust-vr distribute-list to-trust

 

Answer: C

 

 

QUESTION 24

Which ScreenOS CLI commands would match the 10.35.89.0/24 subnet for route redistribution?

 

 

 

 

 

A.

set access-list 20 permit ip 10.35.89.0/24 10

set route-map name harry permit 5

set match ip 20

B.

set access-list 5 permit 10.35.89.0 0.0.0.255

set route-map harry permit 10

set match ip address 5

C.

set address Trust harry 10.35.89.0 255.255.255.0 set distribution-list harrylist 1

set address harry

D.

set address Trust harry 10.35.89.0 255.255.255.0 set route-map harry permit 10

set ospf export harry

 

Answer: A

 

 

QUESTION 25

Which two statements are true about redundant interfaces? (Choose two.)

 

A.

Only one link in a redundant group is active at a time.

B.

You can place up to four interfaces in a redundant group.

C.

All interfaces in the redundant group are active, providing more bandwidth.

D.

Each interface in the redundant group should be connected to a different L2 device.

 

Answer: AD

 

 

QUESTION 26

Which statement defines maximum bandwidth?

 

A.

The total amount of bandwidth (configured in Mbps) that can be used by a policy after guaranteed bandwidth has been serviced.

B.

The total amount of bandwidth (configured in Kbps) that can be used by a policy after all guaranteed bandwidth has been serviced.

C.

The additional amount of bandwidth over the guaranteed bandwidth amount (configured in Kbps) that can be used by a policy after guaranteed bandwidth has been serviced.

D.

The additional amount of bandwidth over the guaranteed bandwidth amount (configured in Mbps) that can be used by a policy after guaranteed bandwidth has been serviced.

 

Answer: B

 

 

 

 

 

QUESTION 27

You are a read/write VSYS administrator. Your configuration requires the use of a DIP.

 

Which statement correctly describes this situation?

 

A.

DIP creation can only be done by the root administrator, not a VSYS administrator.

B.

You can create the DIP on any interface imported into your VSYS, but not on shared interfaces.

C.

You can create DIPs on any interface you can see in your interface list, including both private and shared interfaces.

D.

You can create DIPs only on sub-interfaces within your VSYS. All other DIPs need to be created by the root level VSYS admin.

 

Answer: A

 

 

QUESTION 28

Which three HTTP components can a ScreenOS device inspect and selectively block? (Choose three.)

 

A.

.gz files

B.

.zip files

C.

.exe files

D.

Java applets

E.

JavaScript applets

 

Answer: BCD

 

 

QUESTION 29

What is the correct processing order for a routing lookup on a ScreenOS device?

 

A.

Source route; source-interface route; policy-based route on virtual router; policy-based route on zone; policy-based route on interface

 

 

 

 

B.

Source-interface route; source route; policy-based route on interface; policy-based route on zone; policy-based route on virtual router

C.

Policy-based route on interface; policy-based route on zone; policy-based route on virtual router; source-interface route; source route

D.

Policy-based route on virtual router; policy-based route on zone; policy-based route on interface; source route; source-interface route

 

Answer: C

 

 

QUESTION 30

What is the recommended order of steps to configure inter-VSYS routing?

 

A.

Create VSYS zones; enter VSYS; configure inter-VR routing; configure VSYS interfaces; create VSYS

B.

Create VSYS; enter VSYS; create VSYS zones; configure VSYS interfaces; configure inter-VR routing

C.

Configure VSYS interfaces; create VSYS; create VSYS zones; enter VSYS; configure inter-VR routing

D.

Create VSYS zones; create VSYS; enter VSYS; configure inter-VR routing; configure VSYS interfaces

 

Answer: B

 

Free VCE & PDF File for Juniper JN0-532 Actual Tests

Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …

This entry was posted in JN0-532 Actual Tests (November) and tagged , , , , , , . Bookmark the permalink.