[Free] Download New Latest (November) Juniper JN0-532 Actual Tests 91-100

Ensurepass

QUESTION 91

You have implemented a hub and spoke VPN. On the hub, there are two tunnel interfaces, one to each spoke. Both tunnel interfaces are in the same zone.

 

Which two configuration options will control traffic between the spokes? (Choose two.)

 

A.

Configure the common zone to block intra-zone traffic.

B.

Configure the common zone to block inter-zone traffic.

C.

Configure each tunnel interface to block intra-zone traffic.

D.

Move one of the tunnel interfaces to a different zone and create policies between the two zones.

 

 

 

 

 

Answer: AD

 

 

QUESTION 92

Review the exhibit.

 

clip_image002

 

Based on the exhibit, which of the following statements about this policy are true?

 

A.

The policy is queued at the highest priority.

B.

The policy is currently inactive.

C.

The policy will be processed second in the overall list of rules.

D.

The policy was created using multiple services rather than a service group.

 

Answer: D

 

 

QUESTION 93

What will happen if you type the command unset protocol vrouter trust-vr protocol ospf?

 

A.

OSPF stops running, but the OSPF configuration is left intact.

B.

All OSPF configuration parameters are removed from the vrouter only.

C.

All OSPF configuration parameters are removed from all interfaces in the vrouter.

D.

All OSPF configuration parameters are removed from the vrouter and from all interfaces in the vrouter.

 

Answer: D

 

 

 

 

 

QUESTION 94

As a member of a VSD group, a device may be in which two states? (Choose two.)

 

A.

init

B.

backup

C.

inactive

D.

passive

 

Answer: AB

 

 

QUESTION 95

Click the Exhibit button.

 

clip_image004

 

In the exhibit, the hub and spoke VPN uses route-based VPNs and has intra-zone blocking enabled on the Evil zone.

 

What is the minimum number of policy rules required to establish full, bi-directional communications between all locations?

 

A.

3

B.

4

C.

6

D.

7

 

 

 

 

 

Answer: D

 

 

QUESTION 96

You are using NSRP and enable preempt on a device with a priority of 120. The other device has the default priority set.

 

What will be the result of this action?

 

A.

The device will become master immediately.

B.

The device will only become master if the device with default priority fails.

C.

The device will wait the defined holdtime period and then take over as master.

D.

The device will enter a pending state until the next maintenance window and then assume the master role.

 

Answer: B

 

 

QUESTION 97

You have four policies configured for the egress interface with 10 Mbps physical bandwidth.

 

The policies are configured as follows:

 

Policy 1 – Highest Priority, 1 Mbps guaranteed, 3 Mbps maximum Policy 2 – 1st Priority, 1 Mbps guaranteed, 4 Mbps maximum Policy 3 – 1st Priority, 2 Mbps guaranteed, 2 Mbps maximum Policy 4 – Highest Priority, 2 Mbps guaranteed, 4 Mbps maximum

 

Assuming the policies
are processed in the order shown, which policy will drop traffic first under a full load?

 

A.

Policy 1

B.

Policy 2

C.

Policy 3

D.

Policy 4

 

Answer: D

 

 

 

 

 

QUESTION 98

Click the Exhibit button.

 

clip_image006

 

Which command(s) will remove the ffilter shown in the exhibit?

 

A.

unset ffilter all

B.

delete filter all

C.

unset ffilter 0-2

D.

unset ffilter 0

unset ffilter 1

unset ffilter 2

E.

unset ffilter 2

unset ffilter 1

unset ffilter 0

 

Answer: E

 

 

QUESTION 99

What should you configure to ensure an HA cable failure does not result in both devices attempting to become master?

 

A.

failover count

B.

secondary path

C.

monitor threshold

D.

heartbeat threshold

 

Answer: B

 

 

 

 

 

QUESTION 100

Click the Exhibit button.

 

clip_image008

 

In the exhibit, you need to configure BGP between devices A and C in AS 65200.

 

Which configuration, if any, will be required only on device B?

 

A.

No configuration is required on device B.

B.

You need to configure IBGP, defining devices A and C as BGP peers.

C.

You need to enable OSPF and redistribute BGP routes on devices A and

C.

D.

You need to configure a policy permitting BGP traffic between device A and device C.

 

Answer: D

 

Free VCE & PDF File for Juniper JN0-532 Actual Tests

Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …

This entry was posted in JN0-532 Actual Tests (November) and tagged , , , , , , . Bookmark the permalink.