[Free] Download New Latest (November) Juniper JN0-692 Actual Tests Topic 1, Volume A part 01

Ensurepass

QUESTION 1  (Topic 1)

 

Click the Exhibit button.

 

clip_image002

 

In the exhibit, what happens if the source starts sending multicast traffic toward R1 and there are receivers registered at the RP?

 

A.

R1 encapsulates the multicast packets into a PIM register multicast packet.

B.

R1 encapsulates the multicast packets into PIM join unicast messages.

C.

R1 forwards the multicast packets on the S,G tree towards the RP.

D.

R1 tunnels the multicast packets in PIM register messages toward the RP.

 

Answer: D

 

 

QUESTION 2  (Topic 1)

 

Click the Exhibit button.

 

 

 

 

 

clip_image004

 

You work for ISP

 

A.

Customers of both ISP B and ISP C must be able to reach all of your customers, but your network must not allow transit traffic between ISP B and ISP C.

 

Referring to the exhibit, which two methods could you use? (Choose two.)

 

 

A.Use local preference to prefer the proper routes.

B.

Use the well-known no-transit community.

C.

Use policy to filter routes on AS number.

D.

Use communities to identify and filter routes.

 

Answer: CD

 

 

QUESTION 3  (Topic 1)

 

Router R5 has the overload parameter configured. Which statement is true?

 

A.

R5 will purge its LSAs from the network until the overload condition is cleared.

B.

R5 will increase its link metrics to 65535 and will stop forwarding transit traffic to OSPF destinations.

C.

R5 will increase its link metrics to 65535 and will continue to forward transit traffic to OSPF destinations.

D.

R5 will send an overload LSA to its neighbors to indicate it is in the overload state.

 

 

 

 

 

Answer: C

 

 

QUESTION 4  (Topic 1)

 

Click the Exhibit button.

 

clip_image006

 

Customer A is complaining that CE1 and CE2 cannot form an OSPF adjacency across your LDP Layer 2 circuit. The physical topology of the network is CE1-PE1-P-PE2-CE2. PE1’s loopback is 192.168.5.1, P’s loopback is 192.168.6.1, and PE2’s loopback is 192.168.7.1.

 

Referring to the output in the exhibit, what is the problem?

 

A.

mismatched virtual circuit ID values

B.

mismatched interface encapsulations

C.

incorrect PE-CE interface configuration

 

 

 

 

D.

extended LDP neighbor not established

 

Answer: B

 

 

QUESTION 5  (Topic 1)

 

Click the Exhibit button.

 

clip_image008

 

A LDP Layer 2 circuit is shown for VPN A and VPN

B.LDP tunneling over RSVP is activated on P1 and P2. Referring to the exhibit, which statement is true about the LDP Layer 2 circuit?

 

A.

MAC learning is needed and using the inner VPN label between PE1 and PE2 for VPN A or VPN B.

B.

Targeted LDP sessions are established between PE1, P1 and P2, PE2.

C.

Label stitching must be configured on P1 and P2 for end to end transport LSPs.

D.

LDP must be enabled on the loopback interfaces of PE1 and PE2.

 

Answer: D

 

 

QUESTION 6  (Topic 1)

 

Click the Exhibit button.

 

 

 

 

 

clip_image010

 

Referring to the exhibit, PE2 requires the loopback of PE1 to appear in the inet.3 routing table as a labeled route. Which configuration parameter is specifically required to support this?

 

A.

resolve-vpn

B.

family inet-vpn

C.

traffic-engineering bgp-igp

D.

traffic-engineering mpls-forwarding

 

Answer: A

 

 

QUESTION 7  (Topic 1)

 

clip_image012

 

You are asked to configure an EBGP peering, but the peering does not establish and transitions between the Connect and Active states.

 

 

 

 

Referring to the exhibit, what is causing the problem?

 

A.

The number of messages from the BGP peer has exceeded the receive socket buffer.

B.

An incorrect local AS has been configured in the BGP group configuration.

C.

BGP is waiting to receive a keepalive or notification message from the peer.

D.

The BGP peer has an incorrect address configured, causing a connectivity failure.

 

Answer: D

 

 

QUESTION 8  (Topic 1)

 

Click the Exhibit button.

 

clip_image014

 

Referring to the exhibit, which statement is correct?

 

A.

Only multicasts packets (224.0.1.39) are allowed on the input and output direction.

B.

Auto-RP discovery messages are filtered in the input and output direction.

C.

Rendezvous point announcements are filtered in the output direction.

D.

This filter does not work because the input or output parameter is missing.

 

Answer: C

 

 

QUESTION 9  (Topic 1)

 

You are facing BGP scaling issues and decide to add dedicated route reflectors to your network. You notice that VPN routes are not being advertised by your route reflectors. Which three actions can you take to solve this? (Choose three.)

 

A.

Add a static default route to inet.3 and/or inet6.3 on the route reflectors.

B.

Add a full mesh of MPLS LSPs between all of the route reflectors.

 

 

 

 

C.

Add MPLS LSPs between the route reflectors and their client routers.

D.

Add a static default route to inet.3 and/or inet6.3 on all of the client routers.

E.

Use rib-groups to add IGP routes to inet.3 and/or inet6.3 on the route reflectors.

 

Answer: ACE

 

 

QUESTION 10  (Topic 1)

 

Click the Exhibit button.

 

clip_image016

 

In the exhibit, on which label value does PE1 expect to receive traffic from CE3 for VPN A?

 

A.

2002

B.

3001

C.

3002

D.

2001

 

Answer: A

 

Free VCE & PDF File for Juniper JN0-692 Actual Tests

Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …

This entry was posted in JN0-692 Actual Tests (November) and tagged , , , , , , . Bookmark the permalink.