[Free] Download New Latest (November) Juniper JN0-692 Actual Tests Topic 1, Volume A part 02

Ensurepass

QUESTION 11  (Topic 1)

 

An OSPF neighbor between routers R1 and R2 is stuck in loading state on R2. What are

 

 

 

 

two causes? (Choose two.)

 

A.

OSPF is not enabled on the interfaces.

B.

A firewall filter is blocking OSPF hellos on both sides.

C.

The R1 router has received a corrupted link-state request packet.

D.

The interface MTU is mismatched between the routers.

 

Answer: CD

 

 

QUESTION 12  (Topic 1)

 

Click the Exhibit button.

 

clip_image002

 

R2 is announcing the 10.200/16 network to its IS-IS neighbors. No routing policies have been applied to R3. Referring to the exhibit, will R5 have 10.200/16 as an IS-IS route?

 

A.

Yes; IS-IS level 2 externals are passed from level 2 to level 1 by default.

B.

No; IS-IS level 2 externals are only passed to level 1 if wide-metrics-only is configured

 

 

 

 

on all routers.

C.

Yes; all level 2 routing information is shared throughout an IS-IS domain by default.

D.

No; IS-IS does not announce routes from level 2 to level 1 unless a routing policy is applied.

 

Answer: D

 

 

QUESTION 13  (Topic 1)

 

Click the Exhibit button.

 

clip_image004

 

You work for ISP A, as shown in the exhibit, and must configure R1 to use load balancing across both available links to ISP B’s network. Which command do you use to finish the configuration?

 

A.

set protocols bgp group isp-b multipath

B.

set routing-options forwarding-table export per-packet

C.

set protocols bgp group isp-b multihop

D.

set routing-options forwarding-table load-balance

 

Answer: A

 

 

QUESTION 14  (Topic 1)

 

 

 

 

Click the Exhibit button.

 

clip_image006

 

Based on the output shown in the exhibit, which statement is correct?

 

A.

R3 is the designated intermediate system.

B.

R3 is the backup designated intermediate system.

C.

R3 has been configured with an export policy and is announcing external routes to IS-IS neighbors.

D.

R3 is using both IPv4 and IPv6 resulting in two pseudonodes.

 

Answer: A

 

 

QUESTION 15  (Topic 1)

 

Click the Exhibit button.

 

 

 

 

 

clip_image008

 

The output in the exhibit was captured on an interface. Which three statements are true about the configuration on the router with hostname SaoPaulo? (Choose three.)

 

A.

Wide metrics is not in use.

B.

The router has the overload bit
set to “on”.

C.

Authentication is enabled.

D.

System ID is 1921.6805.2001.

E.

Level 2 routing is enabled.

 

Answer: ACE

 

 

QUESTION 16  (Topic 1)

 

 

 

 

 

clip_image010

 

You have committed a configuration on router R1 as shown in the exhibit. However, it resulted in a (*, G) join for only one group (228.1.1.1) on R1.

 

Which additional configuration would result in the creation of a (*, G) join for the other group (232.1.1.1)?

 

A.

Add relevant configurations for an SSM map.

B.

Enable PIM version 1 on interface xe-5/2/0.0.

 

 

 

 

C.

Configure another RP for the other group

D.

Enable PIM on all interfaces.

 

Answer: A

 

 

QUESTION 17  (Topic 1)

 

Click the Exhibit button.

 

clip_image012

 

You are configuring a new PE router in your Layer 3 VPN. A remote PE router is using the configuration shown in the exhibit. Which configuration is needed to receive customer-vpn routes from the remote PE?

 

 

 

 

 

clip_image014

 

A.

Option A

B.

Option B

C.

Option C

D.

Option D

 

Answer: C

 

 

 

 

 

QUESTION 18  (Topic 1)

 

You have assigned target:65432:100 as the route target for Customer A’s BGP Layer 2 VPN. The PE1 router VRF is configured with vrf-target export target:65432:100.Which configuration on PE2 correctly assigned Customer A’s routes to their VRF?

 

A.

vrf-target target:65432:100

B.

route-target target:65432:100

C.

vrf-target export target:65432:100

D.

route-target export target:65432:100

 

Answer: A

 

 

QUESTION 19  (Topic 1)

 

clip_image016

 

You have been asked to troubleshoot an OSPF problem where the OSPF session will not

 

 

 

 

establish.

 

According to the outputs shown in the exhibit, which statement is true?

 

A.

The hold-time interval is set too low.

B.

There is an MTU mismatch.

C.

The hold-time interval is set too high.

D.

The dead-interval is set too low.

 

Answer: B

 

 

QUESTION 20  (Topic 1)

 

Click the Exhibit button.

 

clip_image018

 

Based on the exhibit, what do you expect to find in the configuration on R1 and R4?

 

A.

a policy leaking level 1 routes into level 2

B.

a policy leaking level 2 routes into level 1

C.

a policy setting the attached bit on level 2 routes

 

 

 

 

D.

a policy setting the attached bit on level 1 routes

 

Answer: B

 

Free VCE & PDF File for Juniper JN0-692 Actual Tests

Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …

This entry was posted in JN0-692 Actual Tests (November) and tagged , , , , , , . Bookmark the permalink.