[Free] Download New Latest (November) Juniper JN0-692 Actual Tests Topic 2, Volume B part 02

Ensurepass

QUESTION 81  (Topic 2)

 

Click the Exhibit button.

 

clip_image002

 

 

 

 

Customer A is complaining that routes advertised from the CE2 router are not being received on the CE1 router. The physical topology of the network is CE1-PE1-PE2-CE2. The CE1-PE1 subnet is 172.16.1.0/24. The CE2-PE2 subnet is 172.16.2.0/24. PE1’s loopback is 192.168.3.1 and PE2’s loopback is 192.168.4.1.Referring to the output in the exhibit, what is the problem?

 

A.

No LSP exists between PE1 and PE2.

B.

Route targets are not properly configured.

C.

as-override is not configured in the VRFs.

D.

family inet-vpn is not configured on the PEs.

 

Answer: C

 

 

QUESTION 82  (Topic 2)

 

Click the Exhibit button.

 

clip_image004

 

In the exhibit, network 172.16.0.0/16 is redistributed into IS-IS in Area 49.0002. R1 must use R2 to access 172.16.0.0/16. All other traffic leaving Area 49.0001 must use R4.Which three steps will accomplish this task? (Choose three.)

 

A.

Configure R1 to ignore the attached bit.

B.

Disable the attached bit on R4 in Area 49.0001.

C.

Enable an L2 adjacency on the link between R1 and R2.

D.

Leak network 172.16.0.0/16 into L1 on R2.

E.

Redistribute a static default route into L1 on R4.

 

 

 

 

 

Answer: ACD

 

 

QUESTION 83  (Topic 2)

 

Click the Exhibit button.

 

clip_image006

 

The IGP is IS-IS. R2 has configured its loopback interface in Level 2 only. Referring to the exhibit, which statement is true?

 

A.

R2 advertises its loopback address to all L1 adjacencies.

B.

R1 cannot reach R2’s loopback address.

C.

R1 uses a default route to reach R2’s loopback address.

D.

R1 automatically selects R2 as the default gateway to reach R2’s loopback address.

 

Answer: C

 

 

QUESTION 84  (Topic 2)

 

Click the Exhibit button.

 

 

 

 

 

clip_image008

 

Given the output in the exhibit, which three statements are correct? (Choose three.)

 

A.

PIM spare-dense mode is used.

B.

PIM sparse mode is used.

C.

The receiver and source 10.255.70.15 are on the shortest path tree.

D.

The receiver and source 10.255.70.15 are on the shared tree.

E.

The receiver and RP are on the shortest path tree.

 

Answer: BCE

 

 

 

 

 

QUESTION 85  (Topic 2)

 

Click the Exhibit button.

 

clip_image010

 

< font face="Arial">You are asked to configure an OSPF network based on the topology shown in the exhibit. Area 1 must not receive Type 5 LSAs from the backbone, but must be capable of containing ASBRs. What will accomplish this?

 

A.

Area 1 should be configured as a stub area, which by default meets the network’s requirements.

B.

R3 should be configured with no-externals for Area 1, which will suppress Type 5 announcements.

C.

R3 should be configured with no-summaries for Area 1, which will suppress Type 5 announcements.

D.

Area 1 should be configured as an NSSA, which by default meets the network’s requirements.

 

Answer: D

 

 

 

 

 

QUESTION 86  (Topic 2)

 

You are asked to design a Layer 2 VPN service between service provider networks that needs Ethernet transport capabilities. The VPN should support two or three endpoints. Which Layer 2 VPN technology should you propose?

 

A.

LDP-signaled VPLS

B.

BGP-signaled VPLS, using the RFC 4448 Layer 2 frame format

C.

LDP Layer 2 circuit, using the RFC 4448 Layer 2 frame format

D.

BGP Layer 2 VPN

 

Answer: B

 

 

QUESTION 87  (Topic 2)

 

Which two configuration parameters are required to configure an LDP-signaled VPLS service? (Choose two.)

 

A.

vpls-id

B.

site-identifier

C.

route-distinguisher

D.

instance-type vpls

 

Answer: AD

 

 

QUESTION 88  (Topic 2)

 

Click the Exhibit button.

 

 

 

 

 

clip_image012

 

You are provisioning a full-mesh BGP Layer 2 VPN for Customer

 

A.

The customer has four remote sites in their network. Using best practices, you assigned interface unit numbers matching the assigned VLAN numbers. Which Layer 2 VPN configuration is correct for PE2?

 

 

 

 

 

clip_image014

 

 

A.Option A

 

 

 

 

B.

Option B

C.

Option C

D.

Option D

 

Answer: C

 

 

QUESTION 89  (Topic 2)

 

You are monitoring the control plane traffic using a network analyzer on an Ethernet network segment with all routers configured with IS-IS routing. Which two statements are true? (Choose two.)

 

A.

DIS will send hellos more frequently than other IS-IS devices.

B.

L1 and L2 hellos are combined in a single hello packet.

C.

PSNPs are sent periodically.

D.

Only the DIS will send CSNPs periodically.

 

Answer: AD

 

 

QUESTION 90  (Topic 2)

 

Click the Exhibit button.

 

clip_image016

 

The exhibit contains a sample trace file of a BGP update message. Which two statements are true? (Choose two.)

 

 

 

 

 

A.

10.10.56.0/30 is a route internal to the AS.

B.

The router that sent this update is the BGP originator of 10.10.56.0/30.

C.

The BGP session is EBGP.

D.

The local preference has been changed from the default settings.

 

Answer: AB

 

Free VCE & PDF File for Juniper JN0-692 Actual Tests

Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …

This entry was posted in JN0-692 Actual Tests (November) and tagged , , , , , , . Bookmark the permalink.