[Free] Download New Latest (November) Juniper JN0-692 Actual Tests Topic 2, Volume B part 04

Ensurepass

QUESTION 101  (Topic 2)

 

What does the Junos command advertise-inactive allow?

 

A.

OSPF inactive routes to be advertised using BGP

B.

inactive and hidden BGP routes to be redistributed into OSPF

C.

the best BGP route to be re-advertised by BGP, even when it is not the best route

D.

the second-best BGP route to be re-advertised by BGP, to back up the best BGP route

 

Answer: C

 

 

QUESTION 102  (Topic 2)

 

Click the Exhibit button.

 

clip_image002

 

In the exhibit, all routers within each AS are configured for Anycast RP. All intra-AS routers

 

 

 

 

are configured within the same MSDP mesh group. Inter-AS multicast has been enabled using MSDP without MSDP mesh groups. Which statement is true?

 

A.

R6 and R7 should have an MSDP peering, because multiple MSDP AS hops are not allowed.

B.

SA messages received from R2 are not forwarded to R5, R7, and R8.

C.

SA messages from R5 are not forwarded to AS1.

D.

Duplicate SA messages may be received in AS2.

 

Answer: D

 

 

QUESTION 103  (Topic 2)

 

Click the Exhibit button.

 

 

 

 

 

What is the significance of RIB groups, as shown in the exhibit?

 

 

 

 

&n
bsp;

A.

RIB groups alter the multicast RPF check table to inet.0.

B.

RIB groups alter the multicast RPF check table to inet.2.

C.

RIB groups alter the multicast RPF check table to inet.4.

D.

RIB groups alter the multicast RPF check table to inet.3.

 

Answer: B

 

 

QUESTION 104  (Topic 2)

 

Click the Exhibit button.

 

clip_image004

 

On your MX Series router, traffic using the voice scheduler has exceeded its transmit rate. All other data is currently in profile. Referring to the exhibit, which statement is correct?

 

 

 

 

 

A.

The voice queue is serviced later than the less-critical queue.

B.

The voice queue is serviced later than the left-over queue.

C.

The voice queue is serviced before the critical queue.

D.

The voice queue is serviced after data queue.

 

Answer: C

 

 

QUESTION 105  (Topic 2)

 

Click the Exhibit button.

 

clip_image006

 

 

 

 

 

clip_image008

 

R1 and R2 are directly connected using the interfaces shown in the exhibit. R1 can ping R2’s interface, and R2 can ping R1’s interface. The IS-IS adjacency will not come up. What is causing the adjacency to fail?

 

A.

The correct levels are not configured under protocols isis.

B.

The link MTU is too small to support IS-IS.

C.

Authentication is not properly configured for the adjacency.

D.

Both routers are configured as the DR, causing a conflict.

 

Answer: B

 

 

QUESTION 106  (Topic 2)

 

Click the Exhibit button.

 

 

 

 

 

clip_image010

 

Given the existing operational network shown in the exhibit, you now want to add a remote site for Customer B to the PE3 router. This change should not have an effect on the existing BGP sessions between the PE routers. Which Layer 3 VPN scaling mechanism allows PE3 to begin receiving Customer B routes?

 

A.

route origin

B.

route refresh

C.

route reflection

D.

route target filtering

 

Answer: B

 

 

QUESTION 107  (Topic 2)

 

Click the Exhibit button.

 

clip_image012

 

 

 

 

Traffic is flowing through the policer as shown in the exhibit. The traffic has a throughput rate of 3 Mbps, and the burst size counter is at 1.5 MB. How is traffic affected?

 

A.

Traffic has its PLP set to low.

B.

Traffic has its PLP set to medium-low.

C.

Traffic has
its PLP set to medium-high.

D.

Traffic has its PLP set to high.

 

Answer: C

 

 

QUESTION 108  (Topic 2)

 

Click the Exhibit button.

 

 

 

 

 

clip_image014

 

A customer has the configuration shown in the exhibit applied to the VRF C-PIM domain.

What can you determine from this configuration?

 

A.

The PE is configured for selective PMSI (S-PMSI) only.

B.

The C-RP is collocated on one of the PEs in the MVPN.

C.

The MVPN is not working because the receiver-site command is missing.

D.

Multicast traffic will not switch to the S-PMSI because the vpn-group-address command (data MDT) is missing.

 

Answer: B

 

 

 

 

 

QUESTION 109  (Topic 2)

 

Click the Exhibit button.

 

clip_image016

 

You are an employee of ISP

 

A.

You must not allow traffic between ISP B and ISP C to cross your network, but customers of ISP B and ISP C must be able to reach your customers. Referring to the exhibit, which two actions would do this? (Choose two.)

 

 

A.Use communities to identify and filter routes.

B.

Use policy to filter routes on AS number.

C.

Use origin code to identify and filter routes.

D.

Use the well-known no-advertise community.

 

Answer: AD

 

 

QUESTION 110  (Topic 2)

 

Click the Exhibit button.

 

 

 

 

 

clip_image018

 

As shown in the exhibit, you have an LSP established from R1 to R4. Your network experiences a link failure between R2 and R3.Which statement is correct?

 

A.

A ResvTear message is sent toward the egress router.

B.

A ResvConf message is sent toward the ingress router.

C.

A PathErr message is sent toward the egress router.

D.

A ResvTear message is sent toward the ingress router.

 

Answer: D

 

Free VCE & PDF File for Juniper JN0-692 Actual Tests

Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …

This entry was posted in JN0-692 Actual Tests (November) and tagged , , , , , , . Bookmark the permalink.