QUESTION 11 (Topic 1)
What is the underlying dynamic link state routing protocol used for the implementation of the Avaya Enterprise Fabric?
|
A. |
OSPF |
|
B. |
OSPFv3 |
|
C. |
IS-IS |
|
D. |
SPBV |
Answer: B
QUESTION 12 (Topic 1)
A technician wants to control the routes being added to the routing table from the BGP routing table. Which statement describes how to do this?
|
A. |
BGP accept filters are applied to all routes from received by BGP peers. |
|
B. |
BGP accept filters are applied only to external route information. |
|
C. |
BGP accept filters are applied toall incoming and outgoing ports. |
|
D. |
BGP adds all new priority routes to the routing table.
|
Answer: A
QUESTION 13 (Topic 1)
Refer to the exhibit.
Virtual Link Aggregation Control Protocol (VLACP) is configured by port, and traffic is only forwarded across the uplinks when VLCAP is up and running correctly.
A = InterSwitch Trunk (IST)
B = SplitMulti-Link Trunk (SMLT)
#1 ERS 8600
#2 ERS 8600
#3 ERS 4500
When configuring VLCAP for the network shown in the exhibit, where should it be configured?
|
A. |
On all IST ports and not SMLT ports. |
|
B. |
On all SMLT links and one of the IST links.
|
|
C. |
On all IST and all SMLT ports. |
|
D. |
On none of the IST or SMLT links depicted in this network. |
Answer: C
< /font>
QUESTION 14 (Topic 1)
Which two functions describe VPFM? (Choose two.)
|
A. |
It is a network health at a glance tool. |
|
B. |
It can correlate faults, traps, and provide notification. |
|
C. |
It is another term for the SNM credential. |
|
D. |
Itisa device configuration tool. |
Answer: AB
QUESTION 15 (Topic 1)
Refer to the exhibit.
Based on the command line output shown in the exhibit, how many Gigabit Ethernet ports are available on this Ethernet Routing Switch (ERS) 8600?
|
A. |
3 |
|
B. |
48 |
|
C. |
52 |
|
D. |
83 |
Answer: B
QUESTION 16 (Topic 1)
A technician is setting up switch clustering using Split Multi-Link Trunking (SMLT).
Which link is configured between the SMLT cluster switches?
|
A. |
Inter-Switch Trunk (IST) |
|
B. |
Multi link Trunk (MLT) |
|
C. |
Split Multi Link Trunk (SMLT) |
|
D. |
LAG Trunk |
Answer: A
QUESTION 17 (Topic 1)
On the Ethernet Routing Switch (ERS) 8800, the Virtual Routing Forwarding (VRF)-Lite feature supports multicast virtualization. Which statements about multicast virtualization are true? (Choose two)
|
A. |
Multicast virtualization is fully supported in high availability mode and there is no interruption to traffic in the event of the failure of a CPU. |
|
B. |
Multicast virtualization requires version 7.1 or later. |
|
C. |
To facilitate multicast route redistribution between VRFs, an external unicast edge router is required. |
|
D. |
Many IGMP and PIM commands that you use on the Global Router also apply to VRFs that create. |
Answer: AD
QUESTION 18 (Topic 1)
During the installation of a unified access solution, the IP address of the wireless switch interface needs to be configured on the ERS 8000. Which IP address must be used in configuration?
|
A. |
Any valid IP address within management VLAN subnet.
|
|
B. |
Any valid IP address within the unified access VLAN subnet. |
|
C. |
The switch CLIP (loopback) address. |
|
D. |
Any reachable valid IP address. |
Answer: C
QUESTION 19 (Topic 1)
An Ethernet Routing Switch (ERS) 8600 is being configured for Virtual Router Redundancy Protocol (VRRP).
If the default value is used on the peer switch, which CLI command would cause this switch to e the VRRP master?
|
A. |
Config vlan 100 ip vrrp 100 priority 250 |
|
B. |
Config vlan 100 ip vrrp 100 priority 1 |
|
C. |
Config vlan 100 ip vrrp 100 master |
|
D. |
Config vlan 100 ip vrrp 100 priority master |
Answer: A
QUESTION 20 (Topic 1)
By default the ERS 8000 is configured for warm standby.
After installation of a new ERS solution with dual CPUs, which three actions need to be Perform on the ERS configuration to ensure high availability mode is enabled and will function correctly? (Choose three)
|
A. |
Set the high availability CPU boot flag to true. |
|
B. |
Set the warm standby CPU hoot flag to false. |
|
C. |
Set the save to standby CPU boot flag to true. |
|
D. |
Save the boot.cfg conflg file and reset the switch to activate the changes. |
|
E. |
Install the high availability license file. |
Answer: ADE
Free VCE & PDF File for Avaya 3605 Real Exam
Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …
100-105 Dumps VCE PDF
200-105 Dumps VCE PDF
300-101 Dumps VCE PDF
300-115 Dumps VCE PDF
300-135 Dumps VCE PDF
300-320 Dumps VCE PDF
400-101 Dumps VCE PDF
640-911 Dumps VCE PDF
640-916 Dumps VCE PDF
70-410 Dumps VCE PDF
70-411 Dumps VCE PDF
70-412 Dumps VCE PDF
70-413 Dumps VCE PDF
70-414 Dumps VCE PDF
70-417 Dumps VCE PDF
70-461 Dumps VCE PDF
70-462 Dumps VCE PDF
70-463 Dumps VCE PDF
70-464 Dumps VCE PDF
70-465 Dumps VCE PDF
70-480 Dumps VCE PDF
70-483 Dumps VCE PDF
70-486 Dumps VCE PDF
70-487 Dumps VCE PDF
220-901 Dumps VCE PDF
220-902 Dumps VCE PDF
N10-006 Dumps VCE PDF
SY0-401 Dumps VCE PDF