[Free] New Updated (October) Avaya 3605 Real Exam Topic 1, Volume A part 03

Ensurepass

 

QUESTION 21  (Topic 1)

 

 

 

 

RSMLT Edge is enabled globally on two ERS 8800 switches. After recovering from a power outage some clients cannot communicate. A technician determined that only one of the core switches has recovered.

 

What should the technician check to ensure that this loss of communication does not occur in the event of a future power outage or other failure?

 

A.

Turn off the Hold Up timer on both core switches.

B.

Increase the Hold Up Timer to 9999 per VLAN for RSMLT Edge support.

C.

Re-enable RSMLT Edge on each of the VLANs on both switches.

D.

Set the VLAN to copy RSMLT info from a similarly configured VLAN.

 

Answer: B

 

 

QUESTION 22  (Topic 1)

 

In a unified access solution that supports mobility, the configuration must allow for the creation of mobility tunnels to the remote switch and needs the reservation of a remote switch in mobility solution?

 

A.

Remote VLANs are dynamically created and will only contain tunnels.

B.

Mobility tunnels are created when needed and mapped to pre-configured existing static VLANs.

C.

Remote VLANS are created with a valid IP address to the tunnel mapping based on the source network.

D.

The remote switch dynamically creates, adds and removes VLANs as required in a mobility solution.

 

Answer: D

 

 

QUESTION 23  (Topic 1)

 

The Ethernet Routing Switch (ERS) 8600 supports the feature IP VPN-Lite that does not require the use of an MPLS network. Which function does the ERS 8600 as a Provider Edge (PE) perform for IP VPN-Lite?’

 

A.

The PE uses the Virtual Routing Forwarding (VRF) instances to provide traffic separation.

B.

The PE provides route exchange with remote PE devices using OSPF.

 

 

 

 

C.

The PE adds a shim header to the Ethernet header specifying which network the packet is crossing.

D.

The PE incorporates Label Distribution Protocol across the core network to connect remote PE devices.

 

Answer: A

 

 

QUESTION 24  (Topic 1)

 

Which statement describes a step in provisioning SPBM in an enterprise network?

 

A.

Configure IP addresses on the core links.

B.

Enable SPBM and IS-IS globally on all nodes and on the core facing links.

C.

Configure the MAC table.

D.

Configure L2 and L3 VSNs on the core SPBM nodes.

 

Answer: B

 

 

QUESTION 25  (Topic 1)

 

Which set of procedures will upgrade the boot monitor on an Ethernet Routing Switch (ERS) 8600 with a single 8692SF module?

 

A.

Copy the new image to flash.

Activate the new image with SF module in service.

B.

Copy the new image to flash.

Boot the new image.

C.

Copy the new image to flash.

Modify the boot choice for run-time change.

Activate the new image SF module in service.

D.

Copy the new image to flash.

Modify the boot choice for run-time image.

Boot the new image.

 

Answer: B

 

 

QUESTION 26  (Topic 1)

 

 

 

 

After experiencing issues with XFPs, the show sys pluggable-optical-modules info CLI commands is used to find that the switch not recognize the XFPs.

 

Which other method can be used to view the XFP compatibility?

 

A.

Check for port alarms

B.

Show DWDM-XFP {default}.

C.

Use the monitor sys tech info command to monitor for any changes in compatibility.

D.

Use enterprise Device Manager and select the Edit, Port, General tab from the navigation pane to display any XFP compatibility issues.

 

Answer: D

 

 

QUESTION 27  (Topic 1)

 

A customer is upgrading an existing ERS 8610 with the 8692SF to software version 7.x.

 

Which statement regarding the upgrade is correct?

 

A.

The customer must upgrade the 8692SF to an 8893SF for software release 7.x.

B.

The customer can run 7.x with the existing 8692SF, although some features will be disabled.

C.

The customer can add the SuperMezz module to the 8692SF and run release 7.x.

D.

The customer must upgrade to an ERS 8810 chassis to run software release 7.x.

 

Answer: C

 

 

QUESTION 28  (Topic 1)

 

A university campus network consists of an Ethernet Routing Switch (ERS) 8000 and Ethernet switches. Recently they implemented Routed Split Multi-Link Trunking (RSMLT) over a split Multi-Link Trunk (SMLT) configuration.

 

What is the advantage of implementing RSMLT over SMLT?

 

A.

RSMLT increases the distance of the SMLT core.

B.

RSMLT achieves better data distribution across the SMLT.

C.

RSMLT extends fast failover benefits to the routed portion of the network.

D.

RSMLT allows the addition new users in a separate building.

 

 

 

 

 

Answer: C

 

 

QUESTION 29  (Topic 1)

 

After issuing a show ist stats (CLI) or show ist stat (ACLI) command, it is determined that the running type is normal MLT and not inter Switch Trunks? (Choose two)

 

A.

The IST is not enabled on the both switches.

B.

The MLT ID does not match on both switches.

C.

The Peer IP address is not the address of the Peer switch IST VLAN.

D.

The peer IP
addresses have to be 192.168.1.1/30 and 192.168.1.2/30.

 

Answer: AC

 

 

QUESTION 30  (Topic 1)

 

While troubleshooting a MultiLink Trunking (MLT) and split MultiLink Trunking (SMLT) network a need arises to determine which link packets are traversing.

 

Which feature should be used to facilitate the troubleshooting?

 

A.

Ping Trace

B.

Ping Snoop

C.

Snoop Trace

D.

Trace Route

 

Answer: B

Free VCE & PDF File for Avaya 3605 Real Exam

Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …

This entry was posted in 3605 Real Exam (October) and tagged , , , , , , . Bookmark the permalink.