[Free] New Updated (October) Juniper TK0-201 Real Exam 161-170

Ensurepass

 

QUESTION 161

On an edge router, you want to create a default route with a next hop to an external connection. The route should be available only when you are receiving routes from the external provider. Which type of route would you configure on your device to accomplish this objective?

 

A.

an aggregate route

B.

a generated route

C.

a primary contributing route

D.

a static route

 

Correct Answer: B

 

 

QUESTION 162

You recently implemented a Layer 2 network using RSTP. Which three statements are true regarding a topology change reconvergence scenario? (Choose three.)

 

A.

Switches do not flush MAC addresses learned from edge ports.

B.

When a port transitions to the discarding state on edge or nonedge ports, TCNs are generated and flooded.

C.

When a port transitions to the forwarding state on nonedge ports, the local switch generates and floods TCNs.

D.

Switches do not flush MAC addresses learned through the same port through which TCNs are received.

E.

When a port transitions to the forwarding state on edge ports, the local switch generates and floods TCNs.

 

Correct Answer: ACD

 

 

QUESTION 163

What is a requirement for link aggregation?

 

A.

Member links must be on continuous ports.

B.

Member links must be on the same switch in a Virtual Chassis.

C.

The speed of the member links must be the same.

D.

LACP must be configured.

 

Correct Answer: C

 

 

QUESTION 164

A router is configured with the configuration shown in the exhibit. Traffic arriving on fe- 0/0/0.0 is not being routed to 10.1.1.1. What can you change to make the device route traffic arriving on fe-0/0/0.0 to 10.1.1.1?

 

clip_image002

 

A.

Add filter-based-forwarding enable to the configuration.

B.

Ensure that the to-10.1.1.1 routing instance has a route to 10.1.1.1.

C.

Add a from statement to the route-to-10.1.1.1 filter.

D.

Explicitly configure an interface in the default route in the to-10.1.1.1 routing instance.

 

Correct Answer: B

 

 

QUESTION 165

As shown in the exhibit, you recently installed four EX Series switches in your network. These switches are using the default RSTP configuration. Which two statements are correct? (Choose two.)

 

clip_image003

 

A.

Switch-4 selects ge-0/0/10.0 as its root port.

B.

Switch-4 selects ge-0/0/9.0 as its root port.

C.

Switch-4’s root cost path is 4000.

D.

Switch-4’s root cost path is 40000.

 

Correct Answer:
BD

 

 

 

 

 

QUESTION 166

What are two switch port default settings on EX Series switches? (Choose two.)

 

A.

Set as trunk mode.

B.

Set with VLAN ID 0.

C.

Set with the native VLAN.

D.

Set as access mode.

 

Correct Answer: BD

 

 

QUESTION 167

You are deploying a Virtual Chassis consisting of four EX4200s. You have powered on all four switches at the same time with the settings shown in the exhibit. Which Virtual Chassis member will become the master?

 

clip_image004

 

A.

Switch-1

B.

Switch-2

C.

Switch-3

D.

Switch-4

 

Correct Answer: D

 

 

 

 

QUESTION 168

Which Junos OS operational mode command provides a high-level view of all configured BGP peers?

 

A.

show bgp group

B.

show bgp neighbor

C.

show bgp summary

D.

show bgp adjacency

 

Correct Answer: C

 

 

QUESTION 169

You see a route in your local routing table that was learned using OSPF. Which command allows you to determine where the route originated?

 

A.

show ospf route

B.

show route protocol ospf

C.

show ospf database

D.

show ospf log

 

Correct Answer: C

 

 

QUESTION 170

What is the purpose of the configuration shown in the exhibit?

 

clip_image005

 

A.

This configuration causes all routes for directly connected interfaces to be installed in oth the inet.0 routing table and the inet.0 routing table for the blue routing instance.

B.

This configuration causes all routes for directly connected interfaces that are assigned to the blue routing instance to be installed in both the inet.0 routing table and the inet.0 routing table for the blue routing instance.

C.

This configuration causes all routes from inet.0 to also be installed in blue.inet.0.

D.

This configuration allows you to specify my-rib-group in a static route’s next-table statement to cause the static route to first try to resolve the address in inet.0 and then in blue.inet.0.

 

Correct Answer: A

Free VCE & PDF File for Juniper TK0-201 Real Exam

Instant Access to Free VCE Files: Juniper | Juniper | SAP …
Instant Access to Free PDF Files: Juniper | Juniper | SAP …

This entry was posted in TK0-201 Real Exam (October) and tagged , , , , , , . Bookmark the permalink.