[Free] New Updated (October) Juniper TK0-201 Real Exam 201-210

Ensurepass

 

QUESTION 201

With which type of IS-IS router can an IS-IS Level 1-only router form an adjacency?

 

A.

any IS-IS Level 1 router of any area

B.

any IS-IS Level 2 router of any area

C.

any properly configured IS-IS router

D.

any IS-IS Level 1 router of the same area

 

Correct Answer: D

 

 

 

 

 

 

QUESTION 202

Router R2 is having adjacency problems with Router R1. Router R2 is stuck in ExStart state. What is causing the problem?

 

A.

There is a physical and data link layer problem between R1 and R2.

B.

There is a misconfigured IP address on the R2 interface.

C.

The hello and dead intervals on R2 do not match R1.

D.

The interface MTU setting on R2 does not match R1.

 

Correct Answer: D

 

 

QUESTION 203

Router-A and Router-B shown in the exhibit are peering between their loopback interfaces. Which operational command on Router-A do you use to display all the BGP routes received from Router-B?

 

clip_image001

 

A.

show route receive-protocol bgp 10.10.10.2 all

B.

show route receive-protocol bgp 10.10.10.1 all

C.

show bgp rib-in neighbor 10.10.10.1

D.

show bgp receive-protocol bgp 10.10.10.2

 

Correct Answer: A

 

 

QUESTION 204

How do two BGP peers signal their capabilities to each other?

 

A.

They include their capabilities in OPEN messages.

B.

They send UPDATE messages with their capabilities after the session is established.

C.

They send CAPABILITIES messages before they send OPEN messages.

D.

The network operator must manually configure the capabilities on both BGP peers.

 

Correct Answer: A

 

 

QUESTION 205

You want to configure a redundant trunk group on a switch. You want ge-0/0/0.0 to be the default link; however, if ge-0/0/0.0 fails and the switch begins using ge-0/0/1.0, you want the switch to continue using ge-0/0/1.0 until ge-0/0/1.0 fails. Which configuration will accomplish this scenario?

 

A.

redundant-trunk-group {

interface ge-0/0/0.0 {

primary;

}

interface ge-0/0/1.0 {

primary;

}

}

B.

redundant-trunk-group {

interface ge-0/0/0.0;

interface ge-0/0/1.0;

no-preempt;

}

C.

redundant-trunk-group {

interface ge-0/0/0.0 {

primary;

}

interface ge-0/0/1.0;

}

D.

redundant-trunk-group {

interface ge-0/0/0.0;

interface ge-0/0/1.0;

}

 

Correct Answer: D

 

 

QUESTION 206

You review the current LSA database and you suspect that your LSA database contains stale or invalid database entries. You need to verify that your router is receiving LSAs from other routers in your network. Which action would you take to correct this problem?

 

A.

Purge the LSDB.

< /td>

B.

Increase the max-age attribute for the LSDB.

C.

Decrease the max-age attribute for the LSDB.

D.

Disable and enable the interfaces.

 

Correct Answer: A

 

 

 

 

 

QUESTION 207

Your customer wants to connect a VoIP phone to interface ge-0/0/5 on an EX4200 switch in VLAN 20 and connect a PC to the VoIP phone. The PC should be part of VLAN 30. Which two commands will implement this solution? (Choose two.)

 

A.

set interface ge-0/0/5.0 family ethernet-switching vlan members vlan-30

B.

set ethernet-switching-options voip interface ge-0/0/5.0 vlan 20

C.

set interface ge-0/0/5.0 family ethernet-switching vlan members vlan-20

D.

set ethernet-switching-options voip interface ge-0/0/5.0 vlan 30

 

Correct Answer: AB

 

 

QUESTION 208

You attach six routers (R1, R2, R3, R4, R5, and R6) to a single Ethernet LAN and configure the routers with addresses in the same subnet. You do not modify the default priority of any router. R1 is chosen as the designated router and R2 is chosen as the backup designated router. How many full adjacencies does R3 have?

 

A.

0

B.

1

C.

2

D.

5

 

Correct Answer: C

 

 

QUESTION 209

You have a traditional 3-tier network design. What are two functions of the aggregation layer? (Choose two.)

 

A.

It functions as the gateway to the WAN edge.

B.

It connects access layer switches.

C.

It provides inter-VLAN routing.

D.

It facilitates device access.

 

Correct Answer: BC

 

 

QUESTION 210

You add a GRE tunnel to transport packets between two routers. After implementing this, you notice an increase in the number of dropped packets. While looking at packet captures, you notice that the do-not-fragment (DF) bit is set in the IP header of all the dropped packets. What would cause this changed behavior?

 

A.

The GRE tunnel has a lower MTU than the physical interface.

B.

GRE tunnels do not support fragmentation.

C.

GRE tunnels do not support the DF bit.

D.

The GRE tunnel has a higher MTU than the physical interface.

 

Correct Answer: A

Free VCE & PDF File for Juniper TK0-201 Real Exam

Instant Access to Free VCE Files: Juniper | Juniper | SAP …
Instant Access to Free PDF Files: Juniper | Juniper | SAP …

This entry was posted in TK0-201 Real Exam (October) and tagged , , , , , , . Bookmark the permalink.