[Free] New Updated (October) Juniper TK0-201 Real Exam 261-270

Ensurepass

 

QUESTION 261

You have been asked to configure a route to 192.168.0.0/16 that will only be active under the following criteria.

 

clip_image002There is an active route to 192.168.100.0/24.

clip_image002[1]The 192.168.100.0/24 route came from the protocol OSPF.

 

Which type of route accomplishes this task?

 

A.

static

B.

generate

C.

aggregate

D.

null

 

Correct Answer: B

 

 

QUESTION 262

Which two statements describe STP and RSTP interoperability? (Choose two.)

 

A.

STP protocol discards any RSTP BPDUs it receives.

B.

STP protocol accepts RSTP BPDUs but will not respond.

C.

RSTP accepts STP BPDUs and responds with STP BPDUs.

D.

RSTP discards STP BPDUs.

 

Correct Answer: AC

 

 

QUESTION 263

Which three statements are true of GRE tunnels? (Choose three.)

 

A.

The local tunnel endpoint must have a valid route to the remote endpoint.

B.

GRE tunnels must authenticate at both ends of the tunnel.

C.

Tunnel endpoints must have a route that directs traffic into a tunnel.

D.

The “gr” interface can only route packets that are IP protocol packets.

E.

All intermediary devices must have a route to the tunnel endpoints.

 

Correct Answer: ACE

 

 

QUESTION 264

Which statement is true regarding the minimum-interval configuration shown below?

 

user@router# show ospf

 

area 0.0.0.0 {

 

interface ge-0/0/1.0 {

 

bfd-liveness-detection {

 

minimum-interval 300;

 

}

 

}

 

}

 

A.

It is the minimum hold time before BFD informs OSPF that the BFD session has been torn down.

B.

It enables minimum transmit and receive intervals for 300 ms.

C.

It enables minimum transmit and receive intervals for 300 seconds.

D.

It is the minimum amount of time that the BFD session must remain alive before changing state.

 

Correct Answer: B

 

 

QUESTION 265

You are analyzing packet captures on your network. You observe an OSPF Type 7 LSA. In which area type did this packet originate?

 

A.

backbone

B.

stub

C.

totally stubby

D.

not-so-stubby area

 

Correct Answer: D

 

 

 

 

 

 

 

 

 

 

QUESTION 266

Refer to the command-line output shown in the exhibit. How many routes has this router received from the BGP peer at 10.10.10.1?

 

clip_image003

 

A.

0 routes

B.

2 routes

C.

3 routes

D.

57 routes

 

Correct Answer: C

 

 

QUESTION 267

You must create an IP-IP tunnel between two routers on your network. These two devices are separated by 10 hops. The tunnel appears to be established, but no traffic is traversing the tunnel. What causes this behavior?

 

A.

The tunnel’s TTL has not been modified from the default value of 8.

B.

Traffic is being dropped along the path because a configured MTU is greater than the tunnel’s MTU.

C.

A route that directs traffic into the tunnel is not present.

D.

BGP has not been enabled between tunnel end-points.

 

Correct Answer: C

 

 

QUESTION 268

You must configure an OSPF area that must not contain any ASBRs and that must not receive any Extern (Type 5) LSAs. This area should be aware of the entire OSPF network, but it should not be aware of routes external to OSPF. Which area type meets these requirements?

 

A.

not-so-stubby area

B.

totally stubby area

C.

stub area

D.

backbone area

 

Correct Answer: C

 

 

 

 

 

 

 

 

 

QUESTION 269

You configure a network according to the topology shown in the exhibit but find that users attached to R7 are having difficulty communicating with the rest of the network. What are two solutions to the problem? (Choose two.)

 

clip_image005

 

A.

Configure Area 3.3.3.3 as a stub area.

B.

Create a virtual link between R3 and R6.

C.

Configure an OSPF export policy on R6 to export routes from Area 2.2
.2.2 to Area 3.3.3.3 and from Area 3.3.3.3 to Area 2.2.2.2.

D.

Connect R6 to Area 0.0.0.0.

 

Correct Answer: B

 

 

QUESTION 270

In the exhibit, Area 2.2.2.2 is configured as a not-so-stubby area and Area 1.1.1.1 is configured as a normal area. R5 has an export policy that causes the RIP network prefixes to be announced through OSPF. Which LSA type does R7 receive describing the RIP network prefixes?

 

clip_image007

A.

Summary (Type 3)

B.

ASBRSum (Type 4)

C.

Extern (Type 5)

D.

NSSA (Type 7)

 

Correct Answer: C

Free VCE & PDF File for Juniper TK0-201 Real Exam

Instant Access to Free VCE Files: Juniper | Juniper | SAP …
Instant Access to Free PDF Files: Juniper | Juniper | SAP …

This entry was posted in TK0-201 Real Exam (October) and tagged , , , , , , . Bookmark the permalink.